DATASHEET
Evo line (5% THID) FN 3442
Ecosine evo, 60 Hz Passive Harmonic Filters
2019
25 Mar 2019
Ecosine passiv
FN 3442: Ecosine evo, 60 Hz Passive Harmonic Filters
  • The industry standard for 6-pulse rectifier and motor drives
  • Filters for diode rectifier without DC-link choke and thyristor rectifier
  • Best-in-class partial load performance
  • Most compact design
  • Plug and play, ready to use
Technical specifications

Nominal operating voltage

3x380 VAC to 415 VAC +-10%

Frequenz

60 Hz ±1 Hz

Nominal motor drive input power rating

1 to 240 HP

Total harmonic current distortion THID*

<5% at rated power

Efficiency

>98% for rated voltage and power

High potential test voltage

P –> E 2160 VAC (1 s)

Protection category

IP 00, IP 20*****

Cooling

Internal fan cooling or external cooling**

Overload capability

1.6x rated current for 1 minute, once per hour

Ambient temperature range

–25°C to +45°C fully operational
+45°C to +70°C derated operation***
–25°C to +85°C transport and storage

Flammability corresponding to

UL 94 V-2

Design corresponding to

Filter: UL 61800-5-1, EN 61800-5-1
Chokes: EN 61558-2-20 or EN 60076-6

MTBF @ 45°C/480 V (Mil-HB-217F)

>200,000 hours

SCCR****

100 kA

Earthing System

TN, TT, IT

Approvals

(depending on filter configuration)

Features and benefits

Schaffner ecosine harmonic filters represent an economical solution to the challenge of load-applied harmonics mitigation in three-phase power systems. With a plug-and-play approach and more compact dimensions than comparable products, they can be quickly installed and easily commissioned. They increase the reliability and service life of electric installations, help utilize electric sytem capacity better, and are the key to meet Power Quality standards such as IEEE 519. Ecosine filters reshape your distorted current back to the desired sinusoidal waveform. Schaffner ecosine filters can be applied to virtually any kind of power electronics with front-end six-pulse rectifiers, 3-phase diode or thyristor bridges, where harmonic current distortion needs to be reduced to defined limits.

Typical applications

  • Equipment with front-end six-pulse rectifier
  • Motor drives
  • Factory automation equipment
  • Water/wastewater treatment facilities
  • Fan and pump applications
  • HVAC installations
  • Mission-critical processes
  • DC fast chargers

Typical electrical schematic

 

 

Filter selection table @ 380 V / 60 Hz – IP 00 enclosure

Filter

Rated load power

Motor driveRated filterWeight

TypicalTerminalFrame

@ 380 V/60 Hz

input currentinput currentlossessize

[kW]

[HP]

[Arms]***[Arms]

[kg]

[lbs][W]****
FN 3442-1-110-E0_ _ _ _ _*0.91.221.375.712.650110A
FN 3442-2-110-E0_ _ _ _ _*1.72.442.747.917.467110A
FN 3442-4-112-E0_ _ _ _ _*2.9474.5710.122.3116112B
FN 3442-6-112-E0_ _ _ _ _*4.46116.9112.728.0132112B
FN 3442-8-112-E0_ _ _ _ _*5.98149.2915.734.6160112C
FN 3442-12-112-E0_ _ _ _ _*8.7122113.8018.039.7237112C
FN 3442-16-113-E0_ _ _ _ _11.9162718.5026.859.1294113D
FN 3442-20-113-E0_ _ _ _ _15.0203423.1030.867.9351113D
FN 3442-24-113-E0_ _ _ _ _17.4244427.835.678.5354113D
FN 3442-32-115-E0_ _ _ _ _23.8325237.246.0101.4459115E
FN 3442-40-115-E0_ _ _ _ _29.3406646.251.1112.6571115E
FN 3442-48-115-E0_ _ _ _ _35.6488355.659.2130.5589115E
FN 3442-60-115-E0_ _ _ _ _44.36010369.359.9132.0821115F
FN 3442-80-115-E0_ _ _ _ _59.48012892.582.4181.61028115F
FN 3442-100-116-E0_ _ _ _ _73.6100165115.0116.2256.11067116G
FN 3442-120-116-E0_ _ _ _ _88.7120208139.0137.1302.21143116G

FN 3442-160-118-E0_ _ _ _ _

118.0160240184.0169.7374.01538118H

FN 3442-200-118-E0_ _ _ _ _**

147.3200320231.0186.9411.91411118H
FN 3442-240-118-E0_ _ _ _ _**177.3240403279.0251.9555.21775118H

*      Filter rating which does not require forced cooling or fan module
**    Filter rating which does not require RC damping module for rectifiers with EMI filter
***  Motor drive input current without harmonic filter
****Typical losses @ 45°C, 380V, 60Hz and rated load power

Filter power terminals

Terminal designation*

Screw thread

Flex wire AWGFlex wireScrew torque value


Max width**Frame size
cable lug
[mm2]  [Nm][lbs·in][mm]
110M314-220.4-2.50.54.47A
112M410-220.4-61.210.610B, C
113M66-180.75-16326.615D
115M81/0-810-50870.815E, F
116M83/0-810-95870.817G
118M103/0-500 kcmil95-2401088.535H

*  Recommended connector type: wire or cable lug for 110 to 113, only cable lug for 115 to 118
** To fulfill creepage/clearance acc. UL 61800-5-1 without additional protection (insulation). Creepage/clearance can vary depending on applicable standard and must be reviewed by customer. Creepage/clearance may be reduced when additional protection (insulation) is provided.

Filter signal and earth terminals

Terminal type

Screw thread

Screw torque value


Frame size
  [Nm][lbs·in]
SignalM3*0.54.4All
Earth (PE)M52.219.5A
Earth (PE)M6435.4B
Earth (PE)M6435.4C
Earth (PE)M8979.7D
Earth (PE)M8979.7E
Earth (PE)M1017150.5F
Earth (PE)M1017150.5G
Earth (PE)M1017150.5H

* Max width cable lug = 7 mm

Filter selection table @ 380 V / 60 Hz – IP 20 enclosure

Filter

Rated load power

Motor driveRated filterWeight

TypicalTerminalFrame

@ 380 V/60 Hz

input currentinput currentlossessize

[kW]

[HP]

[Arms]***[Arms]

[kg]

[lbs][W]****
FN 3442-1-110-E2_ _ _ _ _*0.91.221.37715.450110A
FN 3442-2-110-E2_ _ _ _ _*1.72.442.69919.867110A
FN 3442-4-112-E2_ _ _ _ _*2.9474.571124.3116112B
FN 3442-6-112-E2_ _ _ _ _*4.46.116.911431132112B
FN 3442-8-112-E2_ _ _ _ _*5.98149.2917.438160112C
FN 3442-12-112-E2_ _ _ _ _*8.7122113.802044237112C
FN 3442-16-113-E2_ _ _ _ _11.9162718.503168294113D
FN 3442-20-113-E2_ _ _ _ _15.0203423.103577351113D
FN 3442-24-113-E2_ _ _ _ _17.4244427.84088354113D
FN 3442-32-115-E2_ _ _ _ _23.8325237.252115459115E
FN 3442-40-115-E2_ _ _ _ _29.3406646.257126571115E
FN 3442-48-115-E2_ _ _ _ _35.6488355.665143589115E
FN 3442-60-115-E2_ _ _ _ _44.36010369.367147821115F
FN 3442-80-115-E2_ _ _ _ _59.48012892.5901981028115F
FN 3442-100-116-E2_ _ _ _ _73.6100165115.01252761067116G
FN 3442-120-116-E2_ _ _ _ _88.7120208139.01463221143116G

FN 3442-160-118-E2_ _ _ _ _

118.0160240184.01874121538118H

FN 3442-200-118-E2_ _ _ _ _**

147.3200320231.02044501411118H
FN 3442-240-118-E2_ _ _ _ _**177.3240403279.02695931775118H

*       Filter rating which does not require forced cooling or fan module
**     Filter rating which does not require RC damping module for rectifiers with EMI filter
***   Motor drive input current without harmonic filter
**** Typical losses @ 45°C, 380V, 60Hz and rated load power

Filter power terminals

Terminal designation*

Screw thread

Flex wire AWGFlex wireScrew torque value


Max width**Frame size
cable lug
[mm2]  [Nm][lbs·in][mm]
110M314-220.4-2.50.54.47A
112M410-220.4-61.210.610B, C
113M66-180.75-16326.615D
115M81/0-810-50870.815E, F
116M83/0-810-95870.817G
118M103/0-500 kcmil95-2401088.535H

*  Recommended connector type: wire or cable lug for 110 to 113, only cable lug for 115 to 118
** To fulfill creepage/clearance acc. UL 61800-5-1 without additional protection (insulation). Creepage/clearance can vary depending on applicable standard and must be reviewed by customer. Creepage/clearance may be reduced when additional protection (insulation) is provided.

Filter signal and earth terminals

Terminal type

Screw thread

Screw torque value


Frame size
  [Nm][lbs·in]
SignalM3*0.54.4All
Earth (PE)M52.219.5A
Earth (PE)M6435.4B
Earth (PE)M6435.4C
Earth (PE)M8979.7D
Earth (PE)M8979.7E
Earth (PE)M1017150.5F
Earth (PE)M1017150.5G
Earth (PE)M1017150.5H

* Max width cable lug = 7 mm

 

 

Product selector

Filter configurations

E0XXXXX


- For rectifiers without DC-link
  choke 

 

 

 

E0FAXRX


- For rectifiers without DC-link
  choke and with EMI filter

- Filters contain fan, aux. power 
  supply and RC damper module
 

E0FAJRX and E2FAJRX


- For rectifiers without DC-link
  choke and with EMI filter

- Filters contain fan, aux. power
  supply, RC damper module and
  trap disconnect jumper

Mechanical data of IP 00 enclosure

Frame sizes A-F

Frame sizes G and H

Dimensions

Dimensions in [mm]Dimensions in [in]

Frame

Drill pattern

BaseVolumeDrill patternBaseVolume

R

STUXYZRSTUXYZ
A340120736030216018513.44.70.314.211.96.37.3
B405120742537018020615.94.70.316.714.67.18.1
C460150748343021022118.15.90.319.016.98.38.7
D5401801156049126025221.37.10.422.019.310.29.9
E6802201170563529031926.88.70.427.825.011.412.6
F7302501175268434034328.79.80.429.626.913.413.5
G9202801196086335338636.211.00.437.834.013.915.2
H1115390111150105346245643.915.40.445.341.518.218.0

Inlet air flow required for cooling

Frame size

Min air volume*

[m3/h]CFM [ft3/min]
A, B, C00
D12875
E204120
F, G408240
H612360

* External air flow required for filter configurations without embedded
   ventilation

Mechanical data of IP 20 enclosure

Frame sizes A-D

Frame sizes E-H

Dimensions

Dimensions in [mm]Dimensions in [in]

Frame

Drill pattern

BaseVolumeDrill patternBaseVolume

R

STUXYZRSTUXYZ
A340120736030216018513.44.70.314.211.96.37.3
B405120742537018020615.94.70.316.714.67.18.1
C460150748343021022118.15.90.319.016.98.38.7
D5401801156049126025221.37.10.422.019.310.29.9
E6802201170563529031926.88.70.427.825.011.412.6
F7302501175268434034328.79.80.429.626.913.413.5
G9202801196086335338636.211.00.437.834.013.915.2
H1115390111150105346245643.915.40.445.341.518.218.0

Inlet air flow required for cooling

Frame size

Min air volume*

[m3/h]CFM [ft3/min]
A, B, C00
D12875
E204120
F, G408240
H612360

* External air flow required for filter configurations without embedded
   ventilation

Headquarters, global innovation and development

Switzerland
Schaffner Group
Nordstrasse 11e
4542 Luterbach
T +41 32 681 66 26
info@schaffner.com

To find your local partner within Schaffner‘s global network: www.schaffner.com

© 2018 Schaffner Group

The content of this document has been carefully checked and understood. However, neither Schaffner nor its subsidiaries assume any liability whatsoever for any errors or inaccuracies of this document and the consequences thereof. Published specifica-tions are subject to change without notice. Product suitability for any area of application must ultimately be determined by the customer. In all cases, products must never be operated outside their published specifications. Schaffner does not guarantee the availability of all published products. This disclaimer shall be governed by substantive Swiss law and resulting disputes shall be settled by the courts at the place of business of Schaffner Holding AG. Latest publications and a complete disclaimer can be downloa-ded from the Schaffner website. All trademarks recognized.

Sales and application centers

China
Schaffner EMC Ltd. Shanghai
T20-3 C, No 565 Chuangye Road,
Pudong district
201201 Shanghai
T +86 21 3813 9500
cschina@schaffner.com
www.schaffner.com.cn

Finland
Schaffner Oy
Sauvonrinne 19 H
08500 Lohja
T +358 10 567 2855
finlandsales@schaffner.com

France
Schaffner EMC S.A.S.
16-20 Rue Louis Rameau
95875 Bezons
T +33 1 34 34 30 60
F +33 1 39 47 02 28
francesales@schaffner.com

Germany
Schaffner Deutschland GmbH
Schoemperlenstrasse 12B
76185 Karlsruhe
T +49 721 56910
F +49 721 569110
germanysales@schaffner.com

India
Schaffner India Pvt. Ltd
REGUS WORLD TRADE CENTRE
WTC, 22nd Floor Unit No 2238, Brigade Gateway Campus, 26/1, Dr. Rajkumar Road Malleshwaram (W)
560055 Bangalore
T +91 80 67935355
indiasales@schaffner.com

Italy
Schaffner EMC S.r.l.
Via Ticino, 30
20900 Monza (MB)
T +39 039 21 41 070
italysales@schaffner.com

Japan
Schaffner EMC K.K.  
Taiju-Seimei Sangenjaya Bldg.
1-32-12, Kamiuma, Setagaya-ku
154-0011 Tokyo
T +81 3 5712 3650
F +81 3 5712 3651
japansales@schaffner.com
www.schaffner.jp

Singapore
Schaffner EMC Pte Ltd.
#05-09, Kg Ubi Ind. Estate
408705 Singapore
T +65 6377 3283
F +65 6377 3281
singaporesales@schaffner.com

Spain
Schaffner EMC España
Calle Caléndula 93, Miniparc III, Edificio E
El Soto de Moraleja, Alcobendas
28109 Madrid
T +34 917 912 900
F +34 917 912 901
spainsales@schaffner.com

Sweden
Schaffner EMC AB  
Östermalmstorg 1
114 42 Stockholm
T +46 8 5050 2425
swedensales@schaffner.com
www.schaffner.com

Switzerland
Schaffner EMV AG
Nordstrasse 11
4542 Luterbach
T +41 32 681 66 26
switzerlandsales@schaffner.com

Taiwan R.O.C.
Schaffner EMV Ltd.
20 Floor-2, No 97, Section 1, XinTai 5th Road
22175 XiZhi District New Taipei City 22175
T +886 2 2697 5500
F +886 2 2697 5533
taiwansales@schaffner.com
www.schaffner.com.tw

Thailand
Schaffner EMC Co. Ltd.
Northern Region Industrial Estate
67 Moo 4 Tambon Ban Klang
Amphur Muangg P.O. Box 14

51000 Lamphun
T +66 53 58 11 04
F +66 53 58 10 19
thailandsales@schaffner.com

United Kingdom
Schaffner Ltd.  
5 Ashville Way, Molly Millars Lane
Wokingham
RG41 2PL Berkshire
T +44 118 9770070
F +44 118 9792969
uksales@schaffner.com

USA
Schaffner EMC Inc.
52 Mayfield Avenue
Edison, New Jersey
T +1 732 225 9533
F +1 732 225 4789
usasales@schaffner.com
www.schaffnerusa.com

USA
Schaffner North America
6722 Thirlane Road
24019 Roanoke, Virginia
T +1 276 228 7943
F +1 276 228 7953

USA
Schaffner North America
823 Fairview Road
24382 Wytheville, Virginia
T +1 276 228 7943
F +1 276 228 7258